RYLR330

SHARE

LoRaWAN® Gateway Mini PCIe Card

  • ◆ Designed based on Mini-PCIe form factor 30mm x 59.95mm
  • ◆ Tx power up to 26dBm, Rx sensitivity down to -139dBm@SF12, BW 125KHz
  • ◆ Supports global license-free frequency band (US915, AS923, AU915, KR920, IN865, EU868)
  • ◆ Supports optional USB/SPI interfaces
  • ◆ Support Listen Before Talk
  • ◆ SX1302 baseband processor emulates 8 x 8 channel LoRa® packet detectors, 8 x SF5-SF12 LoRa ® demodulators, 8 x SF5-SF10 LoRa® demodulators, one 125/250/500 KHz high-speed LoRa ® demodulator, and one (G)FSK demodulator

 

 

Description

The RYLR330 is a LoRaWAN® Gateway Module with Mini-PCIe form factor based on Semtech®SX1302/SX1303, SX1250 and SX1261 for Listen Before Talk feature, which enables easy integration into an existing router or other network equipment with LPWAN Gateway capabilities. It can be used in any embedded platform offering a free Mini-PCIe slot with USB/SPI connection. Furthermore, GPS chip and Crypto Co-processor are integrated onboard.

This RYLR330 is a complete and cost-efficient gateway solution offering up to 10 programmable parallel demodulation paths, 8 x 8 channel LoRa® packet detectors, 8 x SF5-SF12 LoRa®demodulators, and 8 x SF5-SF10 LoRa demodulators. It is capable of detecting an uninterrupted combination of pockets at 8 different spreading factors and 10 channels with continuous demodulation of up to 16 packets

Specification

Operating Frequencies

The board supports the following LoRaWAN frequency channels, allowing easy configuration while building the firmware from the source code.

Region Frequency (MHz)
North America US915
Asia AS923
Australia AU915
Korea KR920
Europe EU868

 

 

RF Characteristics

The following table gives typically sensitivity level of the UP100 gateway module.

Signal bandwidth (KHz) Spreading factor Sensitivity (dBm)
125 12 -139
125 7 -125
250 12 -136
250 7 -123
500 12 -134
500 7 -120

 

 

Electrical Requirements

Stressing the device above one or more of the ratings listed in the Absolute Maximum Rating section may cause permanent damage. These are stress ratings only. Operating the module at these or any conditions other than those specified in the Operating Conditions sections of the specification should be avoided. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability.

The operating condition range defines those limits within which the functionality of the device is guaranteed. Where application information is given, it is advisory only and does not form part of the specification.

 

Absolute Maximum Rating

The limiting values given below are following the Absolute Maximum Rating System (IEC 134).

Symbol Desciption Condition Min Max
Operation Voltage +2.7 +3.3 +5 V
Current   10 15 mA
Center Frequency   1561±2.046   MHz
Center Frequency   1575.42±1.023   MHz
Center Frequency   1602±8   MHz
Center Frequency   1176 ±10   MHz
Antenna Impedance   c   Ω
Polarization        
LNA Gain 24   30.5 dB
Antenna Gain 0   3.5 dB
Noise Figure   1   dB
V.S.W.R     2  

WARNING:

The product is not protected against overvoltage or reversed voltages. If necessary, voltage spikes exceeding the power supply voltage specification, given in table above, must be limited to values within the specified boundaries by using appropriate protection devices

 

Maximum ESD

Parameter Min. Typ Max. Remarks
ESD_HBM     1000V Charged Device Model JESD22-C101 CLASS III
ESD_CDM     1000V Charged Device Model JESD22-C101 CLASS III

NOTE:

Although this module is designed to be as robust as possible, electrostatic discharge (ESD) can damage this module. This module must be protected at all times from ESD when handling or transporting. Static charges may easily produce potentials of several kilovolts on the human body or equipment, which can discharge without detection. Industry-standard ESD handling precautions should be used at all times.

 

Power Consumption

Version Mode Condition Max.
SPI Version Active mode (TX) The power of the TX channel is 26dBm and 3.3V supply. 410mA
SPI Version Active mode (RX) TX disabled and RX enabled 45mA
USB Version Active mode (TX) The power of the TX channel is 26dBm and 3.3V supply. 443mA
USB Version Active mode (RX) TX disabled and RX enabled 60mA

 

 

Power Supply Range

Input voltage at 3V3 must be above the normal operating range minimum limit to switch on the module.

Symbol Parameter Min Typical Max
3V3 Module supply operating input voltage 3V 3.3V 3.6V

DATASHEET

File Name Type Updated Preview Download
RYLR330_EN PDF 2023-07-12 Preview download

HAL library

File Name Type Updated Preview Download
RYLR330 HAL library PDF 2023-02-15 Preview download

請稍後...

數據存檔中,請勿關閉或切換頁面!

帳戶登入中...

請勿關閉或切換頁面!